TCP Connection Closing #
Introduction #
When a TCP connection is being set-up, the client and server perform a three-way handshake to ensure the connection is a valid one. The connection is established when sequence numbers have been exchanged and synchronized in both directions. CLOSE is an operation meaning “I have no more data to send.”
The notion of closing a full-duplex connection is subject to ambiguous interpretation, of course, since it may not be obvious how to treat the receiving side of the connection. We have chosen to treat CLOSE in a simplex fashion. The user who CLOSEs may continue to RECEIVE until he is told that the other side has CLOSED also. Thus, a program could initiate several SENDs followed by a CLOSE, and then continue to RECEIVE until signaled that a RECEIVE failed because the other side has CLOSED. We assume that the TCP will signal a user, even if no RECEIVEs are outstanding, that the other side has closed, so the user can terminate his side gracefully. A TCP will reliably deliver all buffers SENT before the connection was CLOSED so a user who expects no data in return need only wait to hear the connection was CLOSED successfully to know that all his data was received at the destination TCP. Users must keep reading connections they close for sending until the TCP says no more data.
There are essentially three cases:
- The user initiates by telling the TCP to CLOSE the connection
- The remote TCP initiates by sending a FIN control signal
- Both users CLOSE simultaneously
Local user initiates the close #
In this case, a FIN segment can be constructed and placed on the outgoing segment queue. No further SENDs from the user will be accepted by the TCP, and it enters the FIN-WAIT-1 state. RECEIVEs are allowed in this state. All segments preceding and including FIN will be retransmitted until acknowledged. When the other TCP has both acknowledged the FIN and sent a FIN of its own, the first TCP can ACK this FIN. Note that a TCP receiving a FIN will ACK but not send its own FIN until its user has CLOSED the connection also.
TCP receives a FIN from the network #
If an unsolicited FIN arrives from the network, the receiving TCP
can ACK it and tell the user that the connection is closing. The
user will respond with a CLOSE, upon which the TCP can send a FIN to
the other TCP after sending any remaining data. The TCP then waits
until its own FIN is acknowledged whereupon it deletes the
connection. If an ACK is not forthcoming, after the user timeout
the connection is aborted and the user is told.
Both users close simultaneously #
A simultaneous CLOSE by users at both ends of a connection causes FIN segments to be exchanged. When all segments preceding the FINs have been processed and acknowledged, each TCP can ACK the FIN it has received. Both will, upon receiving these ACKs, delete the connection.
Normal Close Sequence #
TCP A TCP B
1. ESTABLISHED ESTABLISHED
2. (Close)
FIN-WAIT-1 --> <SEQ=100><ACK=300><CTL=FIN,ACK> --> CLOSE-WAIT
3. FIN-WAIT-2 <-- <SEQ=300><ACK=101><CTL=ACK> <-- CLOSE-WAIT
4. (Close)
TIME-WAIT <-- <SEQ=300><ACK=101><CTL=FIN,ACK> <-- LAST-ACK
5. TIME-WAIT --> <SEQ=101><ACK=301><CTL=ACK> --> CLOSED
6. (2 MSL)
CLOSED
Normal Close Sequence
Simultaneous Close Sequence #
TCP A TCP B
1. ESTABLISHED ESTABLISHED
2. (Close) (Close)
FIN-WAIT-1 --> <SEQ=100><ACK=300><CTL=FIN,ACK> ... FIN-WAIT-1
<-- <SEQ=300><ACK=100><CTL=FIN,ACK> <--
... <SEQ=100><ACK=300><CTL=FIN,ACK> -->
3. CLOSING --> <SEQ=101><ACK=301><CTL=ACK> ... CLOSING
<-- <SEQ=301><ACK=101><CTL=ACK> <--
... <SEQ=101><ACK=301><CTL=ACK> -->
4. TIME-WAIT TIME-WAIT
(2 MSL) (2 MSL)
CLOSED CLOSED
Simultaneous Close Sequence